home *** CD-ROM | disk | FTP | other *** search
- Newsgroups: alt.radio.scanner
- From: riyadth@boi.hp.com (Riyadth Al-Kazily)
- Subject: A (useless?) modification for the PRO-38
- Sender: news@mail.boi.hp.com (News Server Project)
- Message-ID: <ByrCr7.Mvy@mail.boi.hp.com>
- Date: Fri, 4 Dec 1992 23:18:42 GMT
- Organization: Hewlett-Packard Company / Boise, Idaho
- Lines: 95
-
- Modifications for the Radio Shack PRO-38 10ch scanner
-
- These PRO-38 modifications may also apply to the current PRO-41, and
- the Uniden BC50XLT and BC55XLT scanners, which appear to be the same
- unit in different packaging.
-
- Initially I wanted to enable my scanner to receive TV audio bands, just
- for fun. This started a quest for modification information, and I
- learned a lot about what can and can't be done with a scanner.
- Unfortunately, I didn't learn until after I performed this modification
- that TV audio (and FM radio) is broadcast in WFM (wideband FM), but
- most scanners only receive NFM (narrow-band FM). This results in
- major garbling of the sound when the scanner is tuned to a TV audio
- frequency.
-
- Anyway, on with the modification. I purchased the Realistic Service
- Manual for the PRO-38, part number 20-139, for a paltry $5.28 and a
- 1 week order delay. In it I found quite a bit of useful information.
- It contains full board layouts, a block diagram, a detailed schematic,
- and some pinout information for the UNIDEN UC-1143 microprocessor
- which controls frequency selection. This is in addition to the test and
- alignment procedures. There is even a nifty reset/test mode [WHICH
- ERASES STORED FREQUENCIES!], switch on while depressing 2-9-MANUAL.
- This programs all channels to test frequencies.
-
- The first thing I found was the ability to select U.S. or European band
- coverage, through a jumper on the CPU board. Installing this jumper
- (normally missing in the U.S.) changes the VHF-low frequency range from
- 29-54MHz to 66-88MHz. This looked very much like what I wanted for at
- least some of the TV audio reception. But it sounded like garbage, then
- I found out about WFM/NFM... So I removed this mod (I don't know of any
- frequencies in that range that would be useful).
-
- I looked through the service manual some more, and found that there were
- 3 pins on the processor that appeared to be inputs (from the test
- voltages given in the manual) yet were not used or given any other
- designation. I grounded each one of these pins, as I did with the
- European mode jumper, and tested the results. Only one of them made any
- difference, and it too is probably useless. What it did was to change
- the VHF-high frequency range from 136-174MHz to 118-174MHz. This
- extends the frequency coverage into the aircraft band, but this band is
- AM, and this radio does not have any AM detector circuitry (as far as I
- know).
-
- I was hoping that some magic pin would enable 16 channels (as on the
- similar mobile PRO-2025), but I couldn't find one. There is the
- possibility of more keys being added, as the scan matrix is 3x8, but
- only 16 keys are used (8 more could be added). The PRO-2025 has 2 more
- buttons, PRIORITY and WX (weather), and both of these features would be
- nice. Maybe someone else has some ideas? I was thinking of getting the
- PRO-2025 service manual, to see the differences, but I may just get a
- better scanner and be done with it :-)
-
- If anyone out there can come up with more modifications or information
- about this scanner, please let me know. There are quite a few of us out
- there that have simple scanners like this, and we would like to get more
- out of them. Not all beginners go straight to a PRO-2006, after all :-)
-
-
- THE MOD:
-
- European band selection:
- 1. Add a jumper to the digital board, connecting the empty pads near
- the upper left corner of the IC when looking at the board from
- the component side (display up/speaker down - facing away from
- you). When completed you should be able to power up and enter
- frequencies in the 66-88MHz range, with frequencies in the
- 29-54MHz range resulting in E(rror). Note, it should be
- possible to place a small switch on this jumper so that the unit
- can change from European to US modes (probably only when powered
- off). Once a frequency is entered into memory, it can be
- received no matter what bands are enabled.
-
- FM "Air-band" coverage:
- 2. Add a jumper between pin 67 of the microprocessor and ground.
- Pin 67 is one down from the pin connected to the pad used in the
- European band selection, it is the third from the top on the
- left side of the chip. Ground can be obtained at the opposite
- side of the European band jumper pad. Be very VERY careful
- while soldering to the pins of the surface mount chip, and have
- a VERY fine soldering iron tip.
-
- Once the jumper is in place, frequencies can be entered in the
- 118-135MHz range, and no other range is lost.
-
- If you think I take any responsibility for any errors on your part (or
- on my part for that matter), you have another thing coming. No warranty
- is expressed or implied. Use at your own risk.
-
-
- --
- { Riyadth Al-Kazily riyadth@hpdmd48.boi.hp.com riyadth@hpbs1904.boi.hp.com }
- { (208) 323-4987 | When am i going to have time to use all this }
- { Boise, Idaho | stuff I'm collecting? More important, how can }
- { DoD #295 1983 BMW R65 | I get more stuff? Amiga 500+ (+ stuff, that is) }
-
- Copied from the QRZ! Windows Ham Radio CDROM
-
-